Airworthiness Directives; Airbus Helicopters

DEPARTMENT OF TRANSPORTATION <SUBAGY>Federal Aviation Administration</SUBAGY> <CFR>14 CFR Part 39</CFR> <DEPDOC>[Docket No. FAA-2025-0007; Project Identifier MCAI-2023-00998-R]</DEPDOC> <RIN>RIN 2120-AA64</RIN> <SUBJECT>Airworthiness Directives; Airbus Helicopters</SUBJECT> <HD SOURCE="HED">AGENCY:</HD> Federal Aviation Administration (FAA), DOT. <HD SOURCE="HED">ACTION:</HD> Notice of proposed rulemaking (NPRM). <SUM> <HD SOURCE="HED">SUMMARY:</HD> The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Helicopters Model SA341G and SA342J helicopters. This proposed AD was prompted by reports of corrosion on the contact surfaces of the tail rotor inclined and horizontal drive shaft flanges. This proposed AD would require repetitively inspecting the inclined and horizontal drive shaft flanges and, depending on the results, replacing the inclined or horizontal drive shaft. This proposed AD would also prohibit installing certain inclined and horizontal drive shafts unless certain requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products. </SUM> <EFFDATE> <HD SOURCE="HED">DATES:</HD> The FAA must receive comments on this NPRM by March 3, 2025. </EFFDATE> <HD SOURCE="HED">ADDRESSES:</HD> You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • <E T="03">Federal eRulemaking Portal:</E> Go to <E T="03">regulations.gov</E> . Follow the instructions for submitting comments. • <E T="03">Fax:</E> (202) 493-2251. • <E T="03">Mail:</E> U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. • <E T="03">Hand Delivery:</E> Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. <E T="03">AD Docket:</E> You may examine the AD docket at <E T="03">regulations.gov</E> under Docket No. FAA-2025-0007; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above. <E T="03">Material Incorporated by Reference:</E> • For EASA material identified in this proposed AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999 000; email: <E T="03">ADs@easa.europa.eu;</E> website: <E T="03">easa.europa.eu.</E> You may find the EASA material on the EASA website at <E T="03">ad.easa.europa.eu.</E> • You may view this material at the FAA, Office of the Regional Counsel, Southwest Region, 10101 Hillwood Parkway, Room 6N-321, Fort Worth, TX 76177. For information on the availability of this material at the FAA, call (817) 222-5110. It is also available at <E T="03">regulation.gov</E> under Docket No. FAA-2025-0007. <FURINF> <HD SOURCE="HED">FOR FURTHER INFORMATION CONTACT:</HD> Evan Weaver, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (316) 946-4152; email: <E T="03">Evan.P.Weaver@faa.gov</E> . </FURINF> <SUPLINF> <HD SOURCE="HED">SUPPLEMENTARY INFORMATION:</HD> <HD SOURCE="HD1">Comments Invited</HD> The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the <E T="02">ADDRESSES</E> section. Include “Docket No. FAA-2025-0007; Project Identifier MCAI-2023-00998-R” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments. Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to <E T="03">regulations.gov</E> , including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM. <HD SOURCE="HD1">Confidential Business Information</HD> CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Evan Weaver, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (316) 946-4152; email: <E T="03">Evan.P.Weaver@faa.gov.</E> Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking. <HD SOURCE="HD1">Background</HD> EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2023-0168, dated August 31, 2023 (EASA AD 2023-0168) (also referred to as the MCAI), to correct an unsafe condition on all Airbus Helicopters Model SA 341 G and SA 342 J (Gazelle) helicopters. The MCAI states that there have been several reports of corrosion on the contact surfaces of the tail rotor inclined and horizontal drive shaft flanges. More detailed non-destructive testing indicated pitting corrosion on the mating faces of several flanges and further investigation revealed various regions of intergranular failure beneath the surface of corrosion pits. The unsafe condition, if not addressed, could result in the failure of the tail rotor drive and subsequent loss of control of the helicopter. The FAA is issuing this proposed AD to address the unsafe condition on these products. You may examine the MCAI in the AD docket at <E T="03">regulations.gov</E> under Docket No. FAA-2025-0007. <HD SOURCE="HD1">Material Incorporated by Reference Under 1 CFR Part 51</HD> The FAA reviewed EASA AD 2023-0168, which requires repetitively inspecting the flanges of certain part-numbered inclined and horizontal drive shafts for corrosion. If corrosion is found, EASA AD 2023-0168 requires replacing the affected inclined or horizontal drive shaft. EASA AD 2023-0168 also prohibits installing an affected inclined or horizontal drive shaft on any helicopter unless it is a serviceable part as defined within. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the <E T="02">ADDRESSES</E> section. <HD SOURCE="HD1">FAA's Determination</HD> These products have been approved by the aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop on other products of the same type design. <HD SOURCE="HD1">Proposed AD Requirements in This NPRM</HD> This proposed AD would require accomplishing the actions specified in EASA AD 2023-0168, described previously, as incorporated by reference, except for any differences identified as exceptions in the regulatory text of this proposed AD and except as discussed under “Differences Between This NPRM and the MCAI.” <HD SOURCE="HD1">Explanation of Required Compliance Information</HD> In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2023-0168 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2023-0168 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2023-0168 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2023-0168. Material required by EASA AD 2023-0168 for compliance will be available at <E T="03">regulations.gov</E> under Docket No. FAA-2025-0007 after the FAA final rule is published. <HD SOURCE="HD1">Differences Between This NPRM and the MCAI</HD> The material referenced in the MCAI specifies sending corroded parts to Airbus Helicopters, whereas this proposed AD would not require that action. <HD SOURCE="HD1">Costs of Compliance</HD> The FAA estimates that this AD, if adopted as proposed, would affect 63 helicopters of U.S. registry. Labor rates are estimated at $85 per work-hour. Based on these numbers, the FAA estimates the ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ Preview showing 10k of 18k characters. Full document text is stored and available for version comparison. ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━