Airworthiness Directives; Airbus SAS Airplanes

DEPARTMENT OF TRANSPORTATION <SUBAGY>Federal Aviation Administration</SUBAGY> <CFR>14 CFR Part 39</CFR> <DEPDOC>[Docket No. FAA-2025-3988; Project Identifier MCAI-2025-00443-T]</DEPDOC> <RIN>RIN 2120-AA64</RIN> <SUBJECT>Airworthiness Directives; Airbus SAS Airplanes</SUBJECT> <HD SOURCE="HED">AGENCY:</HD> Federal Aviation Administration (FAA), DOT. <HD SOURCE="HED">ACTION:</HD> Notice of proposed rulemaking (NPRM). <SUM> <HD SOURCE="HED">SUMMARY:</HD> The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A330-200, -200 Freighter, -300, -800, and -900 series airplanes. This proposed AD was prompted by the identification of an incorrect shot peening application implemented in production. This proposed AD would require repetitive special detailed inspections (SDIs) of affected central windshield frames and applicable corrective actions. The FAA is proposing this AD to address the unsafe condition on these products. </SUM> <EFFDATE> <HD SOURCE="HED">DATES:</HD> The FAA must receive comments on this proposed AD by January 2, 2026. </EFFDATE> <HD SOURCE="HED">ADDRESSES:</HD> You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • <E T="03">Federal eRulemaking Portal:</E> Go to <E T="03">regulations.gov</E> . Follow the instructions for submitting comments. • <E T="03">Fax:</E> 202-493-2251. • <E T="03">Mail:</E> U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. • <E T="03">Hand Delivery:</E> Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. <E T="03">AD Docket:</E> You may examine the AD docket at <E T="03">regulations.gov</E> under Docket No. FAA-2025-3988; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above. <E T="03">Material Incorporated by Reference:</E> • For European Union Aviation Safety Agency (EASA) material identified in this proposed AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email <E T="03">ADs@easa.europa.eu.</E> You may find this material on the EASA website at <E T="03">ad.easa.europa.eu.</E> It is also available at <E T="03">regulations.gov</E> under Docket No. FAA-2025-3988. • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. <FURINF> <HD SOURCE="HED">FOR FURTHER INFORMATION CONTACT:</HD> Nicholas Benson, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-231-3647; email: <E T="03">nicholas.h.benson@faa.gov.</E> </FURINF> <SUPLINF> <HD SOURCE="HED">SUPPLEMENTARY INFORMATION:</HD> <HD SOURCE="HD1">Comments Invited</HD> The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments using a method listed under the <E T="02">ADDRESSES</E> section. Include “Docket No. FAA-2025-3988; Project Identifier MCAI-2025-00443-T” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments. Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to <E T="03">regulations.gov</E> , including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM. <HD SOURCE="HD1">Confidential Business Information</HD> CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Nicholas Benson, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 206-231-3647; email: <E T="03">nicholas.h.benson@faa.gov.</E> Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking. <HD SOURCE="HD1">Background</HD> EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2025-0071, dated March 31, 2025 (EASA AD 2025-0071) (also referred to as the MCAI), to correct an unsafe condition for certain Airbus SAS Model A330-200, -200 Freighter, -300, -800, and -900 series airplanes. The MCAI states an incorrect shot peening application was implemented in production and the fatigue life of affected central windshield frames could consequently be lower than the certified value. This condition, if not addressed, could adversely affect the structural integrity of the airplane. The FAA is proposing this AD to address the unsafe condition on these products. You may examine the MCAI in the AD docket at <E T="03">regulations.gov</E> under Docket No. FAA-2025-3988. <HD SOURCE="HD1">Material Incorporated by Reference Under 1 CFR Part 51</HD> EASA AD 2025-0071 specifies procedures for repetitive SDIs ( <E T="03">i.e.,</E> high frequency eddy current inspections) for cracking of the windshield central lower framing fillet radius on the left-hand and right-hand sides, and applicable corrective actions. Corrective actions include repair. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the <E T="02">ADDRESSES</E> section. <HD SOURCE="HD1">FAA's Determination</HD> These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop in other products of the same type design. <HD SOURCE="HD1">Proposed AD Requirements in This NPRM</HD> This proposed AD would require accomplishing the actions specified in EASA AD 2025-0071 described previously, except for any differences identified as exceptions in the regulatory text of this proposed AD. <HD SOURCE="HD1">Explanation of Required Compliance Information</HD> In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has been coordinating this process with manufacturers and CAAs. As a result, the FAA proposes to incorporate EASA AD 2025-0071 by reference in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2025-0071 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in EASA AD 2025-0071 does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2025-0071. Material required by EASA AD 2025-0071 for compliance will be available at <E T="03">regulations.gov</E> under Docket No. FAA-2025-3988 after the FAA final rule is published. <HD SOURCE="HD1">Costs of Compliance</HD> The FAA estimates that this AD, if adopted as proposed, would affect 145 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD: <GPOTABLE COLS="4" OPTS="L2,i1" CDEF="s100,25C,25C,25C"> <TTITLE>Estimated Costs for Required Actions</TTITLE> <CHED H="1">Labor cost</CHED> <CHED H="1">Parts cost</CHED> <CHED H="1">Cost per product</CHED> <CHED H="1">Cost on U.S. operators</CHED> <ROW> <ENT I="01">4 work-hours × $85 per hour = $340</ENT> <ENT>$0</ENT> <ENT>$340</ENT> <ENT>$49,300</ENT> </ROW> </GPOTABLE> The FAA has received no definitive data on which to base the cost estimates for the on-condition repairs specified in this proposed AD. <HD SOURCE="HD1">Authority for This Rulemaking</HD> Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpar ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ Preview showing 10k of 18k characters. Full document text is stored and available for version comparison. ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━