Airworthiness Directives; Piaggio Aviation S.p.A. Airplanes

DEPARTMENT OF TRANSPORTATION <SUBAGY>Federal Aviation Administration</SUBAGY> <CFR>14 CFR Part 39</CFR> <DEPDOC>[Docket No. FAA-2025-2272; Project Identifier MCAI-2025-00818-A]</DEPDOC> <RIN>RIN 2120-AA64</RIN> <SUBJECT>Airworthiness Directives; Piaggio Aviation S.p.A. Airplanes</SUBJECT> <HD SOURCE="HED">AGENCY:</HD> Federal Aviation Administration (FAA), DOT. <HD SOURCE="HED">ACTION:</HD> Notice of proposed rulemaking (NPRM). <SUM> <HD SOURCE="HED">SUMMARY:</HD> The FAA proposes to adopt a new airworthiness directive (AD) for certain Piaggio Aviation S.p.A. (Piaggio) Model P-180 airplanes. This proposed AD was prompted by a report of leakage from the flexible hydraulic hoses connected to the hydraulic pump package (HPP). This proposed AD would require replacing the affected flexible hydraulic hoses. This proposed AD would also prohibit installing the affected flexible hydraulic hoses on any airplane. The FAA is proposing this AD to address the unsafe condition on these products. </SUM> <EFFDATE> <HD SOURCE="HED">DATES:</HD> The FAA must receive comments on this NPRM by October 20, 2025. </EFFDATE> <HD SOURCE="HED">ADDRESSES:</HD> You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • <E T="03">Federal eRulemaking Portal:</E> Go to <E T="03">regulations.gov.</E> Follow the instructions for submitting comments. • <E T="03">Fax:</E> (202) 493-2251. • <E T="03">Mail:</E> U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. • <E T="03">Hand Delivery:</E> Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. <E T="03">AD Docket:</E> You may examine the AD docket at <E T="03">regulations.gov</E> under Docket No. FAA-2025-2272; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above. <E T="03">Material Incorporated by Reference:</E> • For Piaggio Aerospace material identified in this proposed AD, contact Piaggio, P180 Customer Support, via Pionieri e Aviatori d'Italia, snc—16154 Genoa, Italy; phone: +39 331 679 74 93; email: <E T="03">technicalsupport@piaggioaerospace.it.</E> • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 901 Locust, Kansas City, MO 64106. For information on the availability of this material at the FAA, call (817) 222-5110. <FURINF> <HD SOURCE="HED">FOR FURTHER INFORMATION CONTACT:</HD> Adam Hein, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; phone: (316) 946-4116; email: <E T="03">adam.hein@faa.gov</E> . </FURINF> <SUPLINF> <HD SOURCE="HED">SUPPLEMENTARY INFORMATION:</HD> <HD SOURCE="HD1">Comments Invited</HD> The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments using a method listed under <E T="02">ADDRESSES</E> . Include “Docket No. FAA-2025-2272; Project Identifier MCAI-2025-00818-A” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend this proposal because of those comments. Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov, including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM. <HD SOURCE="HD1">Confidential Business Information</HD> CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Adam Hein, Aviation Safety Engineer, FAA, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking. <HD SOURCE="HD1">Background</HD> The European Union Aviation Safety Agency (EASA), which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2025-0102, dated May 5, 2025 (EASA AD 2025-0102) (also referred to as the MCAI), to correct an unsafe condition on Piaggio Model P-180 Avanti and Avanti II airplanes, manufacturer serial numbers 1002, 1004 to 1234 inclusive, and 3001 to 3018 inclusive. The MCAI states that leakage from the flexible hydraulic hoses was reported on a Model P-180 airplane. A subsequent investigation revealed that the failure of the HPP electrical motor caused an anomalous current to return through the HPP body, resulting in electrical arcing. This arcing, which occurred as the HPP body was in contact with a flexible steel braided hose, punctured the flexible hydraulic hose. Additionally, the improper installation of the HPP, specifically the incorrect routing of the hydraulic flexible lines according to the airplane maintenance manual, contributed to the incident. This condition, if not detected and corrected, could lead to leaks developing in the flexible hydraulic hoses, which could result in loss of the hydraulic system or fire in the HPP area. To address the unsafe condition, the MCAI requires replacing the affected flexible hydraulic hoses with a new serviceable part. You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA-2025-2272. <HD SOURCE="HD1">Material Incorporated by Reference Under 1 CFR Part 51</HD> The FAA reviewed Piaggio Aerospace Service Bulletin 80-0497, Revision 0, dated March 5, 2025 (Piaggio SB 80-0497, Revision 0). This material specifies procedures for replacing the affected flexible hydraulic hoses with new flexible hydraulic hoses that have a non-metallic and non-conductive abrasion sleeve covering the steel braid which will provide electrical insulation that can prevent arcing and electrostatic discharge in case of accidental contact between the flexible hydraulic hoses and HPP body. This material is reasonably available because the interested parties have access to it through their normal course of business or by means identified in the <E T="02">ADDRESSES</E> section. <HD SOURCE="HD1">FAA's Determination</HD> These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI and material referenced above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop on other products of the same type design. <HD SOURCE="HD1">Proposed AD Requirements in This NPRM</HD> This proposed AD would require accomplishing the actions specified in the material already described. This proposed AD would also prohibit installing the affected flexible hydraulic hoses on any airplane. <HD SOURCE="HD1">Costs of Compliance</HD> The FAA estimates that this AD, if adopted as proposed, would affect 107 airplanes of U.S. registry. The FAA estimates the following costs to comply with this proposed AD: <GPOTABLE COLS="5" OPTS="L2,nj,i1" CDEF="s50,r50,10,12,12"> <TTITLE>Estimated Costs</TTITLE> <CHED H="1">Action</CHED> <CHED H="1">Labor cost</CHED> <CHED H="1">Parts cost</CHED> Cost on U.S. operators </CHED> <ROW> <ENT I="01">Replace flexible hydraulic hoses</ENT> <ENT>22 work-hours × $85 per hour = $1,870</ENT> <ENT>$1,241</ENT> <ENT>$3,111</ENT> <ENT>$332,877</ENT> </ROW> </GPOTABLE> <HD SOURCE="HD1">Authority for This Rulemaking</HD> Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. <HD SOURCE="HD1">Regulatory Findings</HD> The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities amo ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ Preview showing 10k of 16k characters. Full document text is stored and available for version comparison. ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━